Offgrid Atlas

Solar Charge Controller Calculator

Pick a charge controller that can handle your array current and voltage. The calculator covers MPPT and PWM types and checks the cold-weather voltage limit.

Reading Your Result

For MPPT controllers, the result is a current rating in amps. It's the array watts divided by battery voltage, with a 25 percent safety margin, rounded up to the next standard size. Above 100 A, the practical choice is several controllers sharing the array.

The second check is voltage. A controller's max PV rating is a hard limit, and panels make their highest voltage on the coldest morning. If cold Voc comes out above the controller rating, you need fewer panels in each series string or a higher-rated controller.

How It's Calculated

Formula

MPPT amps = array W ÷ battery V × 1.25

MPPT current. Round up to 10, 20, 30, 40, 50, 60, 80, or 100 A.
Formula

PWM amps = Isc × parallel strings × 1.25

PWM current. PWM controllers pass panel current straight to the battery, so panel voltage must match the battery.
Formula

Cold Voc = Voc × series × (1 + |coef %| ÷ 100 × (25 − lowest °C)), minimum series Vmp ≥ charge V + 5

Voltage checks. Cold Voc must stay below the controller's max PV, such as 75, 100, 150, 200, or 250 V. Charge voltage is about 14.4 V per 12 V of battery.

Worked Examples

Worked example · Brazil, MPPT on a 24 V bank

The array is 3 panels in series, each 400 W, so 1,200 W total. The battery is 24 V.

Current = 1,200 ÷ 24 × 1.25 = 50 × 1.25 = 62.5 A, which rounds up to 80 A.

Each panel has Voc 41 V and a −0.29 percent per °C coefficient. At a 5°C low, the factor is 1 + 0.0029 × 20 = 1.058.

Cold Voc = 41 × 3 × 1.058 = 130.1 V, below a 150 V limit. An 80 A, 150 V controller fits.

Charge voltage is 28.8 V for a 24 V bank, so the series Vmp needs 33.8 V or more. Three panels at 34 V give 102 V.

Worked example · Kenya, PWM on a 12 V bank

The array is 2 parallel strings of 12 V panels, each with Isc 9.5 A.

Current = 9.5 × 2 × 1.25 = 19 × 1.25 = 23.75 A.

Rounding up gives a 30 A PWM controller.

PWM needs panels with a nominal voltage close to the battery, so use 12 V nominal panels here.

Common Mistakes

  • Sizing by panel watts divided by 12 V when the battery is actually 24 V or 48 V.
  • Checking the controller against Voc at 25°C instead of the cold Voc.
  • Pairing a PWM controller with high-voltage grid-style panels. The mismatch wastes most of the output.
  • Ignoring the controller's own max PV watts rating for the battery voltage chosen.

Frequently Asked Questions

MPPT or PWM, which should I choose?

MPPT harvests more energy and accepts higher-voltage strings, which allows thinner wire over longer runs. PWM costs less and works for tiny 12 V systems with matching panels.

Why is there a 1.25 multiplier?

Sunlight can briefly exceed rated conditions when clouds edge past the sun. The extra 25 percent keeps the controller from running at its limit.

What if my result is over 100 A?

Split the array into groups and give each group its own controller. Several mid-size controllers are easier to source and fail more gracefully than one huge unit.

Does the controller need a minimum number of panels in series?

Yes. The series Vmp must clear the battery charge voltage by at least 5 V, or the controller can't push current into the bank, especially on hot days.

Where does the controller connect first, the battery or the panels?

Connect the battery first so the controller can detect system voltage, then the panels. Reverse that order on shutdown, and follow the maker's manual and local code.

Related Calculators and Guides

Results are estimates based on typical values and the settings above. Local electrical codes apply, and a qualified installer should check the final design before you buy or wire anything. Read the full disclaimer.