How to Size an Off-Grid Solar System, Step by Step
6 min read · Published 2026-11-01 · Last updated 2026-11-17 · Offgrid Atlas Editorial
An off-grid system has four main parts: panels, a battery bank, a charge controller, and an inverter. Each part depends on the one before it, so the order of the math matters. Start with how much energy you use each day, then work through the array, the battery, and the electronics. This guide walks through each step with real numbers.
Start With Daily Energy
Everything else follows from one number, your daily energy in watt-hours (Wh). List every load, write down its power in watts, and estimate the hours it runs each day. Multiply watts by hours to get Wh per load. If you're unsure of a number, the appliance energy calculator helps you estimate it.
Split the list into two groups. DC loads run straight from the battery, such as 12 V lights or a DC fan. AC loads need the inverter, such as a laptop charger, TV, or fridge. The inverter wastes some energy, so AC loads get an extra step.
Daily Wh = DC Wh + (AC Wh ÷ 0.92)
Say a home in Arizona runs 400 Wh of DC loads and 1,600 Wh of AC loads each day. The AC share becomes 1,600 ÷ 0.92 = 1,739.13 Wh. Add the DC load and the daily total is 2,139.13 Wh.
Find Your Design Sun Hours
Peak sun hours measure how much usable sunlight your site gets per day. One peak sun hour equals 1,000 watts of sunlight per square meter for one hour. A cloudy winter day might give 2 hours, while a desert summer day can give 7 or more.
Size the array for your worst month, not your average. If the system covers your load in December, it covers it in June. Sizing for the average leaves you short for months at a time. Look up monthly values for your site with the peak sun hours calculator, then pick the lowest month you'll actually use the system in.
A cabin used only in summer can use a summer value. A home lived in all year needs the winter value. Cold sites need extra care, and the guide on designing solar for winter and cold climates covers it in detail.
Size the Solar Array
The array has to produce your daily energy during the design sun hours. Real panels never reach their rated output in the field, because of heat, dust, wiring loss, and angle. A derate of 0.80 covers those losses. It doesn't include inverter loss, which you already handled in the daily energy step.
Array watts = daily Wh ÷ (sun hours × 0.80)
Back to the Arizona home. Assume the worst month gives 4.5 sun hours. Multiply 4.5 by 0.80 to get 3.6. Then 2,139.13 ÷ 3.6 = 594.2 W. Round up to the next practical panel size. Two 300 W panels give 600 W and cover the need.
Use the solar panel size calculator to check your own numbers, and see the series vs parallel wiring guide for how to connect the panels.
Size the Battery Bank
The battery stores energy for nights and bad weather. Three choices drive its size.
- Days of autonomy, which is how many days the battery must carry the load with no sun
- Depth of discharge, which is how much of the battery you can safely use
- Round-trip efficiency, which is how much stored energy comes back out
Read more about the first in how many days of battery autonomy you need. Depth of discharge and round-trip efficiency depend on the battery type, which the LiFePO4 vs lead-acid guide explains.
Battery nameplate Wh = daily Wh × days ÷ (DoD × round-trip efficiency × temperature factor)
These defaults are a good starting point.
| Battery Type | Depth of Discharge | Round-Trip Efficiency | | --- | --- | --- | | LiFePO4 | 0.90 | 0.95 | | AGM | 0.50 | 0.85 | | Flooded lead-acid | 0.50 | 0.80 | | Gel | 0.50 | 0.85 |
Lead-acid temperature factors are 1.00 at 25°C, 0.90 at 10°C, 0.80 at 0°C, 0.70 at minus 10°C, and 0.60 at minus 20°C. LiFePO4 uses 1.00 at 0°C or above and 0.85 below that. Never charge LiFePO4 below 0°C without a heating system, since it can damage the cells.
Pick System Voltage, Controller, and Inverter
System voltage depends on the array size. Higher voltage means lower current, which means thinner wire and smaller losses.
| Array Size | System Voltage | | --- | --- | | Under 1,000 W | 12 V | | 1,000 W to 3,000 W | 24 V | | Over 3,000 W | 48 V |
The charge controller moves power from the array to the battery. For an MPPT controller, divide array watts by battery voltage, add a 25 percent margin, and round up to a standard size of 10, 20, 30, 40, 50, 60, 80, or 100 A. The charge controller calculator does this for you. The MPPT vs PWM guide explains when to choose each type.
The inverter size depends on the AC loads that run at the same time. Add their running watts, multiply by 1.25, then round up to the next standard size from 300, 600, 1,000, 1,500, 2,000, 3,000, 4,000, 5,000, 6,000, 8,000, or 10,000 W. Motors and compressors briefly draw more at startup, so check surge watts too. The inverter size calculator and the guide to choosing the right inverter size cover this in more depth.
Full Example for a Cabin in Pakistan
Worked example · Cabin in Lahore
A small cabin near Lahore needs these loads each day.
- DC fan, 20 W for 6 hours = 120 Wh DC
- Fridge, 600 Wh per day
- Laptop, 60 W for 5 hours = 300 Wh
- TV, 80 W for 3 hours = 240 Wh
Daily energy. The AC loads total 600 + 300 + 240 = 1,140 Wh. Divide by 0.92 to get 1,239.13 Wh. Add the 120 Wh DC load for a daily total of 1,359.13 Wh.
Array. Assume the worst month at this site gives 4.0 design sun hours. 4.0 × 0.80 = 3.2, so 1,359.13 ÷ 3.2 = 424.7 W. Two 250 W panels give 500 W.
System voltage. An array under 1,000 W uses 12 V.
Controller. 500 ÷ 12 = 41.67 A, and × 1.25 = 52.08 A. Round up to a 60 A MPPT controller.
Battery. The owner wants 2 days of autonomy with LiFePO4 at 25°C. That's 1,359.13 × 2 = 2,718.26 Wh. The divisor is 0.90 × 0.95 × 1.00 = 0.855, so 2,718.26 ÷ 0.855 = 3,179.25 Wh. At 12 V, that's about 265 Ah.
Inverter. The running AC loads are a 150 W fridge, a 60 W laptop, and an 80 W TV. They total 290 W. 290 × 1.25 = 362.5 W, so a 600 W inverter works. Check that it handles the fridge compressor surge.
Check the Design Before You Buy
Run the full design through the off-grid planner, which links these steps in one place. Then check a few details.
- Wire sizes, using the solar wire size calculator to limit voltage drop
- Cold open-circuit voltage, using the cold Voc calculator, so the array never exceeds the controller limit
- Backup power, if the system has a generator, using the generator backup calculator
Treat these results as a solid starting point rather than a final answer. Add a margin for loads you expect to grow, and recheck the numbers whenever you add an appliance.
Related Calculators and Guides
Results are estimates based on typical values and the settings above. Local electrical codes apply, and a qualified installer should check the final design before you buy or wire anything. Read the full disclaimer.