LiFePO4 vs Lead-Acid Batteries for Solar
6 min read · Published 2026-11-01 · Last updated 2026-11-17 · Offgrid Atlas Editorial
Two battery families dominate off-grid solar. Lithium iron phosphate (LiFePO4) is the newer choice, and lead-acid is the long-time standard. Both store energy well, but they behave differently in daily use, in the cold, and over the years. This guide compares them with real sizing numbers, so the choice comes down to your site and your load rather than a sales pitch.
The Short Answer
For most full-time off-grid homes, LiFePO4 is the better fit because it gives more usable energy per battery and handles daily cycling well. Lead-acid still makes sense in a few cases. Examples include a tight upfront budget, a weekend cabin, or a site where charging happens in freezing weather and heating the bank isn't practical.
Chemistry is only one of the sizing inputs. The how to size an off-grid solar system guide shows where the battery fits in the full design.
How the Two Chemistries Differ
The table below summarizes the main practical differences.
| Feature | LiFePO4 | AGM and Gel | Flooded Lead-Acid | | --- | --- | --- | --- | | Usable depth of discharge | 0.90 | 0.50 | 0.50 | | Round-trip efficiency | 0.95 | 0.85 | 0.80 | | Weight for the same usable energy | Lightest | Heavy | Heaviest | | Maintenance | None | None | Check water, vent gas | | Cycle life | Typically several thousand | Hundreds to about a thousand | Hundreds to about a thousand | | Charging in freezing weather | Not allowed without heating | Allowed | Allowed |
Cycle life varies by brand and by how deeply the battery is discharged, so check the manufacturer's datasheet for the exact cycle rating at your planned depth.
Usable Capacity and Efficiency
A battery's label shows its nameplate capacity, but only part of that is safe to use. Depth of discharge (DoD) is the share of the nameplate you can draw down without shortening battery life. A 10 kWh LiFePO4 battery at 0.90 DoD gives 9 kWh of usable energy. A 10 kWh lead-acid bank at 0.50 DoD gives only 5 kWh.
Round-trip efficiency is the share of energy you get back after charging. LiFePO4 returns 95 percent, so little is lost. Flooded lead-acid returns about 80 percent, so one fifth of the solar energy turns into heat. That loss forces you to buy more panels as well as more battery.
The two factors multiply. LiFePO4 gives 0.90 × 0.95 = 0.855 of its nameplate as delivered energy. AGM gives 0.50 × 0.85 = 0.425. Flooded gives 0.50 × 0.80 = 0.40. In plain terms, a LiFePO4 battery delivers about twice as much usable energy per nameplate watt-hour as a lead-acid one.
Battery nameplate Wh = daily Wh × days ÷ (DoD × round-trip efficiency × temperature factor)
Cold Weather Rules
Temperature changes the math. Lead-acid batteries lose capacity as they cool, and the sizing formula captures that with a temperature factor.
| Battery Temperature | Lead-Acid Factor | | --- | --- | | 25°C | 1.00 | | 10°C | 0.90 | | 0°C | 0.80 | | Minus 10°C | 0.70 | | Minus 20°C | 0.60 |
LiFePO4 uses a factor of 1.00 at 0°C or above and 0.85 below that. It has a bigger rule, though. LiFePO4 must not be charged below 0°C unless a heater warms the cells. Charging frozen lithium cells can plate metal inside them and cause permanent damage. Many LiFePO4 batteries include low-temperature charge cutoffs or built-in heaters, which is worth checking before you buy.
For more on planning around cold, read the guide on designing solar for winter and cold climates.
Sizing Both Chemistries Side by Side
Suppose a household needs 2,000 Wh per day and wants 2 days of autonomy. The stored energy target is 2,000 × 2 = 4,000 Wh. At 25°C the nameplate sizes come out as follows.
| Battery Type | Divisor | Nameplate Needed | | --- | --- | --- | | LiFePO4 | 0.855 | 4,678 Wh | | AGM | 0.425 | 9,412 Wh | | Gel | 0.425 | 9,412 Wh | | Flooded | 0.400 | 10,000 Wh |
The lead-acid banks need roughly double the nameplate capacity. Ask how much weight, floor space, and cabling that adds before you assume a cheaper battery gives a cheaper system. The battery bank size calculator runs these numbers for any chemistry and any location.
Cold Cabin Example in Norway
Worked example · Cabin in Norway
A year-round cabin in northern Norway uses 2,000 Wh per day and wants 2 days of autonomy. The battery room drops to minus 10°C in the coldest weeks. The stored energy target is 4,000 Wh.
LiFePO4. The temperature factor below 0°C is 0.85. The divisor is 0.90 × 0.95 × 0.85 = 0.72675. So 4,000 ÷ 0.72675 = 5,504 Wh. This assumes the battery has a heater or a heated enclosure so it can charge.
AGM. The lead-acid factor at minus 10°C is 0.70. The divisor is 0.50 × 0.85 × 0.70 = 0.2975. So 4,000 ÷ 0.2975 = 13,445 Wh.
Flooded. The divisor is 0.50 × 0.80 × 0.70 = 0.28. So 4,000 ÷ 0.28 = 14,286 Wh.
The cold hurts lead-acid far more in size terms. The AGM bank is about 2.4 times the LiFePO4 bank (13,445 ÷ 5,504 = 2.44). If a heated battery space is possible, LiFePO4 wins clearly here. If not, the lead-acid bank can still charge in freezing weather, but it must be much larger.
When Lead-Acid Still Makes Sense
Lead-acid works well where the load is modest, the climate is mild, and the upfront budget is the main limit. A shop in Kenya with reliable sun is a good case.
Worked example · Shop in Nairobi, Kenya
A small shop uses 1,500 Wh per day and wants 1 day of autonomy. The battery sits at about 25°C, so the temperature factor is 1.00.
- LiFePO4 needs 1,500 ÷ 0.855 = 1,754 Wh nameplate
- AGM needs 1,500 ÷ 0.425 = 3,529 Wh nameplate
- Flooded needs 1,500 ÷ 0.40 = 3,750 Wh nameplate
At 12 V, the flooded bank is 3,750 ÷ 12 = 312.5 Ah. The LiFePO4 bank is 1,754 ÷ 12 = 146 Ah. Flooded batteries are also easier to replace in many regions. The owner has to add distilled water on schedule and keep the room ventilated, though.
Local supply matters too. If only lead-acid batteries are stocked nearby and service is hard to reach, a bank you can repair locally may beat a better battery you can't get.
Safety and Installation Basics
Both types can cause fires or burns if wired badly. Fit a correctly rated fuse or breaker close to the battery, use cable sized for the current, and keep terminals tight. Flooded batteries release hydrogen when charging, so they need ventilation. LiFePO4 batteries need a battery management system (BMS) that guards against overcharge, over-discharge, and over-current.
Charge settings must match the chemistry. Using a lead-acid profile on a LiFePO4 battery, or the reverse, shortens battery life. Check the charge controller calculator for sizing, and the battery runtime calculator to see how long a bank powers a given load.
Making the Choice
Pick LiFePO4 if the system runs daily, space and weight matter, and the battery stays above freezing or has a heater. Pick lead-acid if the budget is tight, the load is small, or the bank must charge in freezing weather with no heat source. Either way, size the bank with the right DoD, efficiency, and temperature factor, and let the numbers show the real cost of each path.
Related Calculators and Guides
Results are estimates based on typical values and the settings above. Local electrical codes apply, and a qualified installer should check the final design before you buy or wire anything. Read the full disclaimer.