Offgrid Atlas

Battery Runtime Calculator

See how many hours your battery bank can run a given load before it hits its safe discharge limit. Enter the voltage, capacity, chemistry, and the load in watts.

Reading Your Result

The result is the time a full battery lasts at a steady load. It uses only the usable share of the bank, set by depth of discharge, so a 200 Ah lead-acid battery gives far less than 200 Ah of real runtime.

AC loads cost more than DC loads at the same label wattage, because the inverter draws extra from the battery to cover its own loss. Real runtime also falls when loads change or batteries age, so treat the number as an upper bound and leave some spare hours.

How It's Calculated

Formula

Hours = (V × Ah × DoD) ÷ load draw

Runtime. Usable Wh is V × Ah × DoD. DoD is 0.90 for LiFePO4 and 0.50 for AGM, flooded, and gel.
Formula

Load draw = load W ÷ 0.92 for AC, or load W for DC

Load draw. The 0.92 is inverter efficiency.

Worked Examples

Worked example · Pakistan, outage backup with LiFePO4

A 12 V, 200 Ah LiFePO4 battery has 12 × 200 = 2,400 Wh. Usable = 2,400 × 0.90 = 2,160 Wh.

The AC load is 300 W, so battery draw = 300 ÷ 0.92 = 326.1 W.

Runtime = 2,160 ÷ 326.1 = 6.62 hours.

That's about 6 hours and 37 minutes.

Worked example · Australia, camper trailer with AGM

A 24 V, 100 Ah AGM bank has 24 × 100 = 2,400 Wh. Usable = 2,400 × 0.50 = 1,200 Wh.

A 150 W DC compressor and light load draws 150 W with no inverter loss, so runtime = 1,200 ÷ 150 = 8.0 hours.

If the same 150 W ran through an inverter, draw = 150 ÷ 0.92 = 163.0 W.

Runtime would drop to 1,200 ÷ 163.0 = 7.36 hours.

Common Mistakes

  • Entering the full Ah rating and ignoring depth of discharge.
  • Using peak load watts instead of the average watts over the period.
  • Forgetting that cold temperatures shrink usable capacity, especially in lead-acid.
  • Skipping the inverter's idle draw when the load is small.

Frequently Asked Questions

Does the result include solar charging during the day?

No. It assumes the battery runs alone with no solar input. Real runtime is longer if panels are feeding the bank.

Why is runtime shorter at higher loads?

Heavy draw wastes more energy as heat inside the battery, and lead-acid loses capacity quickly under heavy load. Treat results at high discharge rates as optimistic.

Can I run the bank all the way to 0 percent?

You can, but depth of discharge limits protect battery life. LiFePO4 is built to give about 90 percent, while lead-acid is limited to 50 percent.

What if I have two batteries in parallel?

Add their amp-hours at the same voltage. Two 100 Ah batteries in parallel act as one 200 Ah battery.

How do I stretch runtime in an outage?

Turn off the biggest loads first, and swap heating and cooking appliances for gas or other fuels. Cutting a 300 W load to 150 W doubles the time.

Is there a quick way to check my answer?

Divide usable watt-hours by the watts the battery supplies. If a 2,000 Wh usable bank runs a 500 W load, you get about 4 hours.

Related Calculators and Guides

Results are estimates based on typical values and the settings above. Local electrical codes apply, and a qualified installer should check the final design before you buy or wire anything. Read the full disclaimer.