Offgrid Atlas

Designing Solar for Winter and Cold Climates

7 min read · Published 2026-11-01 · Last updated 2026-11-17 · Offgrid Atlas Editorial

Winter is the hardest season for any off-grid system. Days get short, the sun sits low, snow covers panels, and cold changes how both panels and batteries behave. A system sized for June will run out of power in December. This guide shows how to size for the worst month, protect the battery, and keep panel voltage inside safe limits.

Why Winter Sets the Size of Your System

An off-grid system has no grid to fill gaps, so the darkest month decides the design. Size for summer and the array looks fine on paper for six months, then fails when the loads stay the same and the sun doesn't. Offgrid Atlas uses the worst month by default for this reason.

Three things change in the cold.

  • Sun hours drop, sometimes by a factor of four or more
  • Panel voltage rises, which can damage a controller that was sized for mild weather
  • Battery capacity shrinks, and some chemistries can't charge at all below freezing

The full sizing guide covers the basic steps. This page covers what changes when winter is the limit.

Find Your Worst-Month Sun Hours

Use the peak sun hours for the lowest month at your tilt angle, not the yearly average. The peak sun hours calculator gives monthly values for your location.

The table shows how much the worst month matters. Each row sizes an array for the same daily load of 1,600 Wh. The sun hour values are rounded examples, so check your own site.

| Location | Worst-month sun hours | Array watts for 1,600 Wh | | --- | --- | --- | | Southern Norway, December | 1.25 | 1,600 W | | Lahore, Pakistan, December | 4.0 | 500 W | | Arizona, December | 5.0 | 400 W |

The same cabin needs four times the panels in Norway that it needs in Arizona. Shading, snow, and fog widen the gap further, so avoid sites where a hill or tree line blocks the low winter sun.

Size the Array for the Dark Months

Start with daily energy. Inverter efficiency (0.92) applies once, to AC loads only. Then divide by sun hours and the 0.80 derate. The derate covers heat, dust, wiring, and mismatch losses, and it does not include inverter loss.

Formula

Array watts = daily Wh ÷ (sun hours × 0.80)

Use the worst month's sun hours. Daily Wh = DC Wh + AC Wh ÷ 0.92.

Worked example · Cabin in Southern Norway

A weekend cabin used through the winter has these loads.

  • DC loads (lights, pump, USB charging) use 400 Wh a day
  • AC loads (laptop, small fridge, router) use 1,104 Wh a day

Daily energy = 400 + 1,104 ÷ 0.92 = 400 + 1,200 = 1,600 Wh.

December sun hours at a steep tilt are about 1.25.

Array watts = 1,600 ÷ (1.25 × 0.80) = 1,600 ÷ 1.00 = 1,600 W.

Four 400 W panels cover it. At 1,600 W the array falls in the 1,000 to 3,000 W band, so the system voltage is 24 V.

Controller current = 1,600 ÷ 24 × 1.25 = 66.7 × 1.25 = 83.3 A, which rounds up to a 100 A MPPT controller.

In June the same cabin would need only 1,600 ÷ (5.0 × 0.80) = 400 W, so the winter design leaves a large surplus in summer. That surplus is the price of reliable winter power.

If four times the panels costs too much, cut the load or add a generator for the darkest weeks. The generator backup calculator shows how many run hours a shortfall needs.

Cold Raises Panel Voltage

Panel voltage rises as temperature falls. A string that stays safe at 25 C can exceed a controller's limit on a frozen morning. Use the cold Voc value, never the label value, for this check.

Formula

Cold Voc = Voc × series panels × (1 + |temp coef %| ÷ 100 × (25 − lowest temp C))

Cold Voc must stay below the controller's maximum PV voltage (75, 100, 150, 200, or 250 V).

Take the Norway panel with a Voc of 41.0 V and a temperature coefficient of -0.27 percent per degree C. Two in series give a label Voc of 82.0 V. The table shows what happens as the lowest expected temperature falls.

| Lowest temperature | Cold Voc, 2 panels in series | | --- | --- | | 25 C | 82.0 V | | 10 C | 85.3 V | | 0 C | 87.5 V | | -10 C | 89.7 V | | -20 C | 92.0 V | | -30 C | 94.2 V |

At -30 C the string reaches 94.2 V. That passes a 100 V controller by a thin margin, so a 150 V controller is the safer pick for the cabin. Three in series would reach 41.0 × 3 × 1.1485 = 141.3 V, which needs the 150 V class. Check any other layout with the cold Voc calculator.

Also keep the working voltage (Vmp) at least 5 V above the battery charge voltage. Two panels at 34.0 V each give 68 V, far above the roughly 29 V a 24 V battery needs. The series vs parallel guide explains how to pick a layout. The charge controller calculator checks both limits together.

Cold Changes Battery Capacity

Lead-acid batteries lose usable capacity as they chill. Offgrid Atlas applies a temperature factor to the battery formula.

Formula

Battery Wh = daily Wh × days ÷ (DoD × round-trip efficiency × temperature factor)

Defaults are LiFePO4 0.90 and 0.95, AGM 0.50 and 0.85, flooded 0.50 and 0.80, and gel 0.50 and 0.85.

| Battery temperature | Lead-acid factor | | --- | --- | | 25 C | 1.00 | | 10 C | 0.90 | | 0 C | 0.80 | | -10 C | 0.70 | | -20 C | 0.60 |

LiFePO4 uses 1.00 at 0 C or above and 0.85 below. Compare options for the Norway cabin with two days of autonomy. The load is 1,600 Wh a day, so the energy to store is 1,600 × 2 = 3,200 Wh before losses.

| Battery and conditions | Math | Nameplate Wh | | --- | --- | --- | | LiFePO4, heated room | 3,200 ÷ (0.90 × 0.95 × 1.00) | 3,743 | | LiFePO4, cold space | 3,200 ÷ (0.90 × 0.95 × 0.85) | 4,403 | | AGM, 25 C | 3,200 ÷ (0.50 × 0.85 × 1.00) | 7,529 | | AGM, -10 C | 3,200 ÷ (0.50 × 0.85 × 0.70) | 10,756 |

An AGM bank in an unheated shed at -10 C needs almost three times the capacity of a LiFePO4 bank in a heated room. The battery bank size calculator runs these numbers for your own setup. See LiFePO4 vs lead-acid batteries for the wider comparison, and how many days of battery autonomy for choosing the day count. The depth of discharge and round-trip efficiency pages explain the two ratings in the formula.

Keep LiFePO4 Above Freezing

Many LiFePO4 batteries now ship with low-temperature cutoffs or heating pads. Check the datasheet before buying. Where the battery can't stay warm, three options work.

  • Put the bank in an insulated box inside the heated part of the building
  • Choose a model with self-heating, and size the array to cover the heater's draw
  • Use lead-acid and accept the larger bank shown in the table

Discharging lithium in the cold is usually less of a problem than charging it. Charging is the risk, and the sun often arrives when the air is coldest, at dawn.

Snow, Tilt, and Layout

Snow can block a whole array for days. Mount panels steeply so snow slides off. A tilt near your latitude plus 10 to 15 degrees suits winter use in most places, and a tilt of 60 degrees or more helps where snow is heavy. Keep the lower edge well above the expected snow depth, and leave room to reach panels with a soft brush or roof rake.

Mount panels in landscape or portrait based on how snow will clear and which cells the bottom frame shades. Fewer, longer strings often handle partial shading better in the cold, since a few shaded cells in a series string can drop the whole string.

Check the Design Before You Build

Run these checks in order.

  • Find the worst-month sun hours at your tilt
  • Size the array with the 0.80 derate
  • Calculate cold Voc at the lowest recorded temperature plus a safety margin
  • Pick a controller with a higher PV voltage limit than that value
  • Size the battery with the right temperature factor
  • Decide where the battery will live and how it will stay warm

Local electrical codes apply to every part of this design. Have a qualified installer check the final layout, fusing, and battery enclosure, because cold-weather faults tend to show up at the worst time. The off-grid planner pulls these steps into one project, and the MPPT vs PWM guide explains why MPPT is the usual choice for cold sites with higher string voltages.

Related Calculators and Guides

Results are estimates based on typical values and the settings above. Local electrical codes apply, and a qualified installer should check the final design before you buy or wire anything. Read the full disclaimer.