Offgrid Atlas

Solar Panel Series and Parallel Calculator

Plan how many panels go in each series string and how many strings run in parallel. The calculator checks voltage against your controller and shows the resulting array current.

Reading Your Result

Series wiring adds voltage and keeps current the same. Parallel wiring adds current and keeps voltage the same. The goal is a string voltage high enough to charge the battery and low enough to stay under the controller's limit on the coldest day.

Read the result in three parts. The minimum series count keeps the array above battery charging voltage, the maximum series count comes from cold Voc, and the number of parallel strings sets the total current. If the minimum and maximum don't leave room for your panel count, a different controller or panel is the fix.

How It's Calculated

Formula

Max series = floor(controller max PV ÷ (Voc × (1 + |coef %| ÷ 100 × (25 − lowest °C))))

Maximum panels in series. Use the temperature coefficient of Voc from the panel datasheet.
Formula

Series Vmp ≥ charge V + 5, where charge V ≈ 14.4 × (battery V ÷ 12)

Minimum panels in series. A 48 V battery charges at about 57.6 V, so series Vmp must be at least 62.6 V.
Formula

Array Vmp = Vmp × series, array current = Imp × parallel strings

Array totals. Total panels = series × parallel. Total watts = panels × panel W.

Worked Examples

Worked example · Kenya, six panels on a 48 V bank

Each panel is 300 W with Voc 39 V, Vmp 32 V, Imp 9.4 A, and a −0.29 percent per °C coefficient. The controller limit is 150 V and the lowest temperature is 10°C.

Cold factor = 1 + 0.0029 × (25 − 10) = 1.0435, so cold Voc per panel = 39 × 1.0435 = 40.7 V.

Max series = 150 ÷ 40.7 = 3.68, which means 3 panels. Three panels give 122.1 V cold.

Min series for 48 V = 57.6 + 5 = 62.6 V. Two panels give 64 V, so 2 or 3 in series both work.

Six panels wire as 3 in series × 2 in parallel. Array Vmp = 96 V and current = 2 × 9.4 = 18.8 A.

Worked example · Norway, four panels on a 24 V bank

Each panel is 400 W with Voc 41.5 V, Vmp 34 V, Imp 11.76 A, and a −0.27 percent per °C coefficient. The controller limit is 150 V and the lowest temperature is −25°C.

Cold factor = 1 + 0.0027 × 50 = 1.135, so cold Voc per panel = 41.5 × 1.135 = 47.1 V.

Max series = 150 ÷ 47.1 = 3.18, which means 3 panels. Four in series would reach 188.4 V, so that fails.

Min series for 24 V = 28.8 + 5 = 33.8 V, so 1 panel is enough in theory, but 2 in series gives more headroom.

Wire as 2 in series × 2 in parallel. Cold Voc = 94.2 V, Vmp = 68 V, and current = 2 × 11.76 = 23.5 A.

Common Mistakes

  • Calculating maximum series from Voc at 25°C instead of the coldest expected temperature.
  • Paralleling strings with different panel types, which drags the stronger string down.
  • Skipping string fuses or breakers when three or more strings run in parallel. Check local code for the exact rule.
  • Forgetting that wire and combiner box ratings must cover the higher parallel current.

Frequently Asked Questions

Is series or parallel better for shaded roofs?

Parallel strings tolerate shade better, since a shaded panel only drags its own string. Series gives higher voltage and thinner wire, but shade on one panel cuts the whole string.

Why do series panels need a minimum count?

The controller can only push current into the battery when the array voltage stays above charging voltage. Hot panels lose voltage, so a 5 V buffer keeps charging going in summer.

Can I mix 300 W and 400 W panels?

Within a string, current gets limited by the weaker panel. Put panels of the same model in each string, and match strings in a parallel group.

How many strings can I run in parallel?

The limit is the controller's max input current and the wire and breaker ratings. Check the controller's datasheet, and use string fuses if your local code requires them.

What if my panel count doesn't divide evenly?

Pick a count that fits a clean layout, like 6 as 3 × 2. Adding or dropping a panel is better than mixing uneven strings.

Related Calculators and Guides

Results are estimates based on typical values and the settings above. Local electrical codes apply, and a qualified installer should check the final design before you buy or wire anything. Read the full disclaimer.