Offgrid Atlas

Solar Panel Size Calculator

Find out how many watts of solar panels you need to cover your daily energy use. The calculator also shows how much power the array makes in a month.

Reading Your Result

The array watts figure is the minimum panel capacity that covers your daily use in the design month. Panels rarely produce their label rating, so the formula assumes only 80 percent of the sun's potential reaches your battery.

The panel count is always rounded up. If the calculator says 3.1 panels, you need 4, and the extra output is useful margin on cloudy days. The monthly kWh line shows what that installed capacity makes across the month, so compare it with your monthly use.

How It's Calculated

Formula

Array W = daily Wh ÷ (design sun hours × 0.80)

Array size. Design sun hours are the worst month's peak sun hours at your site, by default.
Formula

Panels = ceil(array W ÷ panel W)

Panel count. Round up, never down. Installed W is panel count × panel W.
Formula

kWh per month = installed W × sun hours × 0.80 × days ÷ 1000

Monthly production. Use the sun hours for that specific month to see seasonal swings.

Worked Examples

Worked example · Arizona, USA, desert home

Daily use is 6,000 Wh. Assume 5.0 peak sun hours in the worst month.

Array = 6,000 ÷ (5.0 × 0.80) = 6,000 ÷ 4.0 = 1,500 W.

With 400 W panels, 1,500 ÷ 400 = 3.75, which rounds up to 4 panels. Installed power is 1,600 W.

Production for a 31-day month = 1,600 × 5.0 × 0.80 × 31 ÷ 1000 = 198.4 kWh.

Monthly use is 6 × 31 = 186 kWh, so the array covers it with 12.4 kWh to spare.

Worked example · Kenya, rural shop

Daily use is 1,500 Wh. Assume 5.0 peak sun hours in the worst month.

Array = 1,500 ÷ (5.0 × 0.80) = 1,500 ÷ 4.0 = 375 W.

With 200 W panels, 375 ÷ 200 = 1.88, which rounds up to 2 panels. Installed power is 400 W.

Production for a 30-day month = 400 × 5.0 × 0.80 × 30 ÷ 1000 = 48 kWh.

Monthly use is 1.5 × 30 = 45 kWh, so the margin is 3 kWh.

Common Mistakes

  • Entering panel wattage as if every panel always makes its full rating.
  • Mixing panels of very different sizes on one controller input without checking voltage and current limits.
  • Rounding the panel count down because it's close to a whole number.
  • Using a daily figure that already has losses added and then adding them again.

Frequently Asked Questions

Why is the factor 0.80 and not 1.0?

Heat, dirt, wire loss, and charge controller loss all take a share. The 0.80 is a practical average across those losses.

Does a bigger array always help?

Only up to what the controller and battery can accept. Extra panels give you more output on gray days, but the controller will clip peak output on bright ones.

Should I pick high-wattage panels or more small ones?

Large panels cost less to mount and wire, while small ones are easier to carry and let you shape the array. Voltage and current limits of your controller decide the layout either way.

How do I find the sun hours for my site?

Use the peak sun hours calculator on this site, which reads NASA POWER monthly data. Pick the lowest month if the system runs all year.

Does panel tilt change the answer?

It does. A tilt near your latitude favors yearly output, while a steeper tilt helps in winter. The calculator assumes a reasonable fixed tilt.

What if my loads change over the year?

Run the calculator for each season and size for the hardest one, or plan a generator to cover the gap.

Related Calculators and Guides

Results are estimates based on typical values and the settings above. Local electrical codes apply, and a qualified installer should check the final design before you buy or wire anything. Read the full disclaimer.