Offgrid Atlas

Peak Sun Hours Calculator for Any City

Look up peak sun hours for any spot on the planet, month by month. The numbers come from NASA POWER, and the lowest month becomes your default design value.

Reading Your Result

One peak sun hour means 1 kWh of sunlight energy per square meter in an hour. NASA POWER's ALLSKY_SFC_SW_DWN value, in kWh/m²/day, equals peak sun hours directly. It's a long-term monthly average, so any single week may run higher or lower.

Read the monthly chart for seasons. A big gap between the best and worst month means a year-round system must be sized for the worst one, or backed by a generator. The calculator also turns each month's value into expected kWh for your array size.

How It's Calculated

Formula

Peak sun hours = irradiation in kWh/m²/day

Peak sun hours. If a source gives MJ/m²/day, divide by 3.6 to convert to kWh/m²/day.
Formula

Design sun = lowest monthly value, array W = daily Wh ÷ (design sun × 0.80)

Design sun hours. Use a seasonal value instead if the system only runs part of the year.
Formula

kWh = installed W × sun hours × 0.80 × days ÷ 1000

Monthly production. Days means the number of days in that month.

Worked Examples

Worked example · South Africa, average versus worst month

Suppose a site has 4.0 peak sun hours in the worst month, June, and a higher yearly average of 5.5. The load is 3,000 Wh per day.

Sizing on the average gives 3,000 ÷ (5.5 × 0.80) = 3,000 ÷ 4.4 = 682 W.

In June, that 682 W array makes 682 × 4.0 × 0.80 = 2,182 Wh, only 73 percent of the daily need.

Sizing on the worst month gives 3,000 ÷ (4.0 × 0.80) = 3,000 ÷ 3.2 = 938 W, which covers June.

Worked example · Norway, summer against winter

Assume 5.0 peak sun hours in June and 0.6 in December for a 1,000 W array.

June, 30 days = 1,000 × 5.0 × 0.80 × 30 ÷ 1000 = 120 kWh.

December, 31 days = 1,000 × 0.6 × 0.80 × 31 ÷ 1000 = 14.9 kWh.

June makes about 8 times more energy than December, so a year-round system here needs a generator or a very large array.

Common Mistakes

  • Using a single yearly average for a system that must run in winter.
  • Mixing units and treating MJ/m²/day as if it were already kWh/m²/day.
  • Treating a long-term average as a guarantee for any given week.
  • Reading sun hours as daylight hours. A 12-hour day can hold only 4 or 5 peak sun hours.

Frequently Asked Questions

What's NASA POWER?

It's a public NASA dataset that gives satellite and model-based solar and weather data for any location. This site uses its long-term monthly averages.

How close are the numbers to a local weather station?

NASA POWER is a gridded estimate, so it can differ from a ground station by several percent. It's a solid starting point for planning in places with no local data.

Does the value account for panel tilt?

The data is for a horizontal surface. A tilted panel can collect more in winter, so the horizontal figure is a safe, conservative start.

Why not design for the best month?

The system would run short for most of the year. The worst month is what decides whether your lights stay on.

What if I only use the system in summer?

Pick the lowest month inside your season. A cabin used from May to September should use the weakest of those five months.

Do clouds and haze show up in the data?

Yes. The all-sky value includes average cloud and aerosol effects, which is why it's lower than clear-sky numbers.

Related Calculators and Guides

Results are estimates based on typical values and the settings above. Local electrical codes apply, and a qualified installer should check the final design before you buy or wire anything. Read the full disclaimer.