Offgrid Atlas

Solar Panel Cold Voc Calculator

Calculate how high your panel string voltage climbs on the coldest morning. Use the result to confirm that your charge controller stays inside its safe input rating.

Reading Your Result

Solar panels make more voltage as they get colder. The label shows Voc at 25°C, but a frosty dawn can push it 10 to 20 percent higher. The result is the number to compare with the controller's max PV rating.

If cold Voc comes in below the limit, the string is safe on voltage. If it's over, remove a panel from the series string or move to a controller with a higher input rating. Going over the limit can destroy a controller, and it often voids the warranty.

How It's Calculated

Formula

Cold Voc = Voc × series × (1 + |coef %| ÷ 100 × (25 − lowest °C))

Temperature correction. Coef is the Voc temperature coefficient in percent per °C. Use the absolute value, since the real number on the datasheet is negative.
Formula

Cold Voc < controller max PV (75, 100, 150, 200, or 250 V)

Controller limits. Local electrical codes may add their own method or safety factor, so confirm what applies at your site.

Worked Examples

Worked example · Norway, mountain cabin

The panel has Voc 49.5 V and a −0.30 percent per °C coefficient. The lowest temperature is −20°C.

Cold factor = 1 + 0.003 × (25 + 20) = 1 + 0.135 = 1.135.

Cold Voc per panel = 49.5 × 1.135 = 56.2 V.

Four in series = 224.7 V, which fits a 250 V controller. Five in series = 280.9 V, which does not.

On a 150 V controller, 150 ÷ 56.2 = 2.67, so only 2 panels fit in series.

Worked example · Australia, frosty Tasmanian valley

The panel has Voc 38.0 V and a −0.28 percent per °C coefficient. The lowest temperature is −5°C.

Cold factor = 1 + 0.0028 × (25 + 5) = 1 + 0.084 = 1.084.

Cold Voc per panel = 38.0 × 1.084 = 41.2 V.

Three in series = 123.6 V, which fits a 150 V controller.

Four in series = 164.8 V, which exceeds 150 V, so keep the string to three panels.

Common Mistakes

  • Using the coefficient for Pmax instead of the one for Voc. Pmax is usually larger, so the answer comes out too high.
  • Using the average winter temperature rather than the record low for the site.
  • Dropping the minus sign and getting a number that suggests voltage falls in the cold.
  • Testing the string at the controller input using hot-day readings and assuming it's safe all year.

Frequently Asked Questions

Where do I find the temperature coefficient?

It's in the panel datasheet under temperature ratings, listed as a percent per °C for Voc. Typical values run from about −0.25 to −0.32 percent.

What lowest temperature should I enter?

Use the coldest temperature expected at the site, such as a local record low or a code-recommended design value. A slightly colder number adds safe margin.

Does the coldest day also mean the sunniest day?

It can. Clear, cold mornings give both high voltage and strong irradiance, which is exactly the worst case for a controller input.

My cold Voc is just under the limit. Is that fine?

It's within spec, but a margin of several percent is wise. Panel variation and an extra cold night can push you close to the edge.

Does hot weather matter for voltage too?

Yes, in the other direction. Hot panels lose voltage, so check that series Vmp still clears battery charging voltage on the hottest day.

Is Voc measured with load or without?

Voc is open circuit, with no load connected. That's the peak voltage before a controller starts drawing current.

Related Calculators and Guides

Results are estimates based on typical values and the settings above. Local electrical codes apply, and a qualified installer should check the final design before you buy or wire anything. Read the full disclaimer.