Offgrid Atlas

Off-Grid Solar Calculator

Enter your daily loads, your location, and your battery type to size the whole system in one pass. The result gives you a daily energy figure, a panel array, a battery bank, a charge controller, and an inverter that fit together.

Reading Your Result

Start with the daily energy number. It's the total your system must make and store every day, with inverter losses added to AC loads only. Every other result builds on it, so a wrong load list throws off the whole design.

The array and battery results answer two different questions. The array tells you how much sun power you need on the worst month of the year, and the battery tells you how long you can run when the sun doesn't show. If one looks far larger than the other, check the days of autonomy and the sun hours before changing anything else.

How It's Calculated

Formula

Daily Wh = DC Wh + AC Wh ÷ 0.92

Daily energy. The 0.92 is inverter efficiency. It's applied once, to AC loads only, so DC loads aren't penalized twice.
Formula

Array W = daily Wh ÷ (design sun hours × 0.80), panels = ceil(array W ÷ panel W)

Array and panel count. The 0.80 covers wiring, heat, dust, and controller losses. Design sun hours default to the worst month.
Formula

Battery Wh = daily Wh × days ÷ (DoD × round-trip efficiency × temperature factor)

Battery bank. Divide the watt-hours by system voltage to get amp-hours.

Worked Examples

Worked example · Pakistan, small home with fans and a fridge

Loads are 300 Wh of DC and 1,200 Wh of AC. Daily energy = 300 + 1,200 ÷ 0.92 = 300 + 1,304 = 1,604 Wh.

Assume 3.5 peak sun hours in the worst month. Array = 1,604 ÷ (3.5 × 0.80) = 1,604 ÷ 2.8 = 573 W.

With 400 W panels, 573 ÷ 400 = 1.43, which rounds up to 2 panels (800 W).

For LiFePO4 at 25°C and 1 day of autonomy, battery = 1,604 ÷ (0.90 × 0.95) = 1,604 ÷ 0.855 = 1,876 Wh.

At 12 V, 1,876 ÷ 12 = 156 Ah, so a 160 Ah battery works.

Worked example · Norway, summer cabin

Loads are 200 Wh of DC and 800 Wh of AC. Daily energy = 200 + 800 ÷ 0.92 = 200 + 870 = 1,070 Wh.

The cabin is used May to September. Assume 3.0 peak sun hours in the worst of those months. Array = 1,070 ÷ (3.0 × 0.80) = 1,070 ÷ 2.4 = 446 W.

With 300 W panels, 446 ÷ 300 = 1.49, which rounds up to 2 panels (600 W).

For AGM at 10°C with 2 days of autonomy, battery = 1,070 × 2 ÷ (0.50 × 0.85 × 0.90) = 2,140 ÷ 0.3825 = 5,595 Wh.

At 12 V, 5,595 ÷ 12 = 466 Ah, so a 470 Ah bank is the next practical size.

Common Mistakes

  • Using the yearly average sun hours instead of the worst month, which leaves the system short for several months of the year.
  • Adding inverter loss to DC loads, which inflates the daily figure and oversizes everything.
  • Forgetting loads that run only part of the day, such as a fridge compressor, and entering the full 24 hours.
  • Sizing the battery without checking the lowest temperature at the site.

Frequently Asked Questions

Do I need every result on this page?

Most systems need all five. A DC-only setup can skip the inverter, and a grid-backup system may skip the large battery bank.

Why does the calculator use the worst month?

A system that works in December also works in June. Sizing for the average means a shortfall in the weakest months.

How much margin should I add on top?

The 0.80 system factor and the battery efficiency terms already include losses. Many people add 10 to 20 percent for future loads, but that's a choice you make, not something the math requires.

Can I run the results on a roof that faces the wrong way?

Orientation and shade cut real output below the estimate. Treat the sun hours as a flat, unshaded, well-tilted array and raise the array size to cover any penalty.

Is this enough to build from?

It's a planning tool. Final wire, fuse, and mounting choices must follow your local electrical code, and a licensed electrician should check high-voltage work.

Related Calculators and Guides

Results are estimates based on typical values and the settings above. Local electrical codes apply, and a qualified installer should check the final design before you buy or wire anything. Read the full disclaimer.