Choosing the Right Inverter Size and Why Surge Matters
7 min read · Published 2026-11-01 · Last updated 2026-11-17 · Offgrid Atlas Editorial
An inverter that's too small trips the first time a fridge or pump starts. One that's too big wastes power all day and costs more than it needs to. The fix is to size for two numbers, the load that runs together and the short burst that motors pull when they start. This guide walks through both with real examples.
Two Ratings Every Inverter Has
Every inverter lists a continuous rating and a surge rating.
- Continuous watts is what the inverter can supply for hours without overheating
- Surge watts is what it can supply for a few seconds, often less than one second
Motors, compressors, and pumps draw several times their running watts as they start. A fridge that runs at 150 W may pull 450 W for a moment when the compressor kicks in. Lights, laptops, and TVs have almost no surge. The surge watts glossary page has more detail.
Both ratings matter. A load that exceeds the continuous rating overheats the inverter and shuts it down after some time. A load that exceeds the surge rating shuts it down at once.
Size the Continuous Rating
Add up the running watts of every AC load that can be on at the same time. Then add 25 percent headroom and round up to the next standard size. Use the appliance energy calculator to find real running watts if the label is unclear.
Inverter continuous W = simultaneous AC running W × 1.25
The 25 percent keeps the inverter below its limit, which helps it run cooler and last longer. Loads that never run together don't add up. A kettle and a washing machine used at different times count once each, not together.
Size the Surge Rating
Surge needs a different method. Only the largest start-up spike counts, because two motors rarely start at the same instant. Take that one load's running watts times its multiplier, then add everything else that's already running.
Surge needed = largest (running W × multiplier) + other simultaneous running W
The multiplier depends on the load. These values are common starting points, and the nameplate or manual is a better source when it lists a starting current.
| Load | Typical multiplier | | --- | --- | | LED lights, phone and laptop chargers, TV | 1.0 | | Ceiling fan | 2.0 | | Power tool | 2.0 | | Fridge or freezer | 3.0 | | Submersible or surface water pump | 3.0 | | Standard (fixed-speed) air conditioner | 3.0 | | Inverter-type air conditioner | 1.5 |
Resistive loads such as kettles, heaters, and irons have little surge, but they have high running watts. They often decide the continuous rating on their own.
Worked Example in Australia
Worked example · Farm Shed in Queensland
A shed in rural Queensland runs these loads at the same time.
| Load | Running W | Multiplier | Surge W | | --- | --- | --- | --- | | Fridge | 150 | 3 | 450 | | Water pump | 750 | 3 | 2,250 | | Lights | 100 | 1 | 100 | | Router and laptop | 120 | 1 | 120 |
Simultaneous running load = 150 + 750 + 100 + 120 = 1,120 W.
Continuous = 1,120 × 1.25 = 1,400 W, which rounds up to a 1,500 W inverter.
The pump has the largest surge at 750 × 3 = 2,250 W. The other loads already running add 150 + 100 + 120 = 370 W.
Surge needed = 2,250 + 370 = 2,620 W.
An inverter rated 1,500 W continuous and 3,000 W surge passes both checks. A model rated 1,500 W continuous and 2,200 W surge passes the first check and fails the second, so the pump would trip it on every start.
Notice how the pump alone shaped the surge need. Without it, the shed would need only a 600 W unit. Water pumps and compressors are the loads most worth checking twice.
Check the DC Side
The inverter pulls current from the battery, and that current can be large. It sets the cable size and the fuse.
Inverter DC input A = continuous W ÷ (system V × 0.92)
For the 1,500 W inverter on a 24 V system, the DC input is 1,500 ÷ (24 × 0.92) = 1,500 ÷ 22.08 = 67.9 A. The fuse is 1.25 × 67.9 = 84.9 A, so the next standard size up is 100 A.
Now check the cable with a 2 m one-way run. Volts lost for 25 mm2 cable is 2 × 2 × 67.9 × 0.0172 ÷ 25 = 0.187 V. As a share of 24 V, that's 0.78 percent. The table compares three cable sizes.
| Cable size | Voltage drop at 24 V | Within 3 percent limit | | --- | --- | --- | | 10 mm2 | 1.95 percent | Yes | | 16 mm2 | 1.22 percent | Yes | | 25 mm2 | 0.78 percent | Yes |
On a 12 V system the same inverter draws 1,500 ÷ (12 × 0.92) = 135.9 A. The same 25 mm2 cable then loses 2 × 2 × 135.9 × 0.0172 ÷ 25 = 0.374 V, which is 3.12 percent of 12 V. That fails the 3 percent limit. Higher system voltage cuts current and cable cost. See voltage drop and AWG if you work in American cable sizes, or use the solar wire size calculator.
Worked Example in Pakistan
Worked example · Home in Lahore
A Lahore home wants to run these loads together during a power cut.
- Three ceiling fans at 70 W each, 210 W total
- Lights at 90 W
- A fridge at 180 W
- A TV at 100 W
- A fixed-speed air conditioner at 900 W
Running total = 210 + 90 + 180 + 100 + 900 = 1,480 W.
Continuous = 1,480 × 1.25 = 1,850 W, which rounds up to a 2,000 W inverter.
The air conditioner has the largest surge at 900 × 3 = 2,700 W. The other loads add 1,480 − 900 = 580 W.
Surge needed = 2,700 + 580 = 3,280 W.
An inverter-type air conditioner with a multiplier of 1.5 changes the surge to 900 × 1.5 = 1,350 W plus 580 W = 1,930 W. The continuous size stays at 2,000 W, but the surge requirement drops by more than 1,300 W, so a cheaper inverter model may suffice.
On a 24 V system the DC input is 2,000 ÷ (24 × 0.92) = 90.6 A, and the fuse is 1.25 × 90.6 = 113.2 A, so a 125 A fuse. On 48 V the same inverter draws 2,000 ÷ (48 × 0.92) = 45.3 A, and the fuse is 1.25 × 45.3 = 56.6 A, so a 60 A fuse.
Pure Sine Wave and Idle Draw
Choose a pure sine wave inverter for fridges, pumps, fans, and any device with a motor or a sensitive power supply. Modified sine wave units can cause noise, heat, and early failure in these loads.
Every inverter also uses some power just by being on. A unit with a 25 W idle draw uses 25 × 24 = 600 Wh a day, even with nothing connected. That's a real share of a small system's budget. Check the idle figure on the datasheet and include it in your watt-hours total. Oversizing makes this worse, since larger inverters usually idle higher. Better to pick the smallest size that passes both checks.
Ways to Lower the Surge You Need
Surge is often the hardest number to meet, and a few changes help.
- Stagger start-ups so two motors never begin together
- Choose a pump or AC with a soft starter or variable speed drive
- Switch to an inverter-type air conditioner
- Put the largest motor on its own timer or relay
The inverter size calculator applies the continuous and surge rules to your list of loads. The how to size an off-grid solar system guide shows where the inverter fits into the whole plan, and the solar backup guide shows the same method applied to outages.
Final Checklist
Before buying, confirm these points.
- Continuous rating is at least 1.25 times the loads that run together
- Surge rating covers the largest start-up plus the other running load
- The inverter output is pure sine wave
- DC fuse and cable match the DC input amps
- Voltage drop from battery to inverter stays under 3 percent
Plug your loads into the off-grid planner to get a full system with these numbers already linked together.
Related Calculators and Guides
Results are estimates based on typical values and the settings above. Local electrical codes apply, and a qualified installer should check the final design before you buy or wire anything. Read the full disclaimer.