Offgrid Atlas

What Size Wire From Solar Panels to the Charge Controller

5 min read · Published 2026-11-17 · Last updated 2026-11-17 · Offgrid Atlas Editorial

For a typical home array, the wire from the panels to the charge controller lands between 4 mm2 and 16 mm2 (about 10 AWG to 4 AWG). Take four 550 W panels wired two in series and two strings in parallel, with a 20 m run to the controller. That setup needs 16 mm2, because 10 mm2 loses 2.3 percent of your power. This guide shows how to get your own number from three inputs, string voltage, current, and run length.

How Big a Wire Do the Panels Need?

Two checks decide the answer. The wire has to carry the current without overheating, and it has to keep voltage drop low. You need a size that passes both.

For the current check, use the panel's short-circuit current, or Isc, from the datasheet. Multiply it by the number of parallel strings, then by 1.25. The wire's ampacity has to be at least that figure.

For the drop check, the site aims for 2 percent or less. Anything above that is voltage drop eating your power, and you pay for it on every sunny day.

What Gauge Wire Do I Need for the Panel Run?

Start with these steps.

  • Find the string voltage by multiplying the panel's Vmp by the number of panels in series
  • Find the current by multiplying Isc by the number of parallel strings
  • Measure the one-way run length, not the round trip
  • Test sizes from small to large until one passes both checks
Formula

Drop % = (2 × length m × current A × 0.0172 ÷ wire mm2) ÷ string V × 100

Length is one way. The 2 covers the trip out and back, and 0.0172 is copper resistivity.

The solar wire size calculator runs this for you. The steps below show what it's doing, so you can check it.

Why Does String Voltage Change the Wire?

Voltage is the big lever. The same power at a higher voltage means fewer amps, and fewer amps mean less drop in the same wire. Drop is measured as a share of circuit voltage, so a higher voltage helps twice.

Wiring panels in series raises voltage and keeps current low. Wiring them in parallel does the opposite. Both layouts can work, but they need very different cable. The series vs parallel wiring guide covers the layout tradeoffs, and the series and parallel calculator tests your strings against the controller limits.

Worked example · Four Panels in Pakistan

A workshop in Pakistan has four 550 W panels. Example datasheet values are Vmp 41.5 V and Isc 13.9 A. They're wired two in series, with two strings in parallel.

  • String voltage is 41.5 × 2 = 83 V
  • Current is 13.9 × 2 = 27.8 A
  • Ampacity needed is 27.8 × 1.25 = 34.75 A
  • One-way run is 20 m

Try 10 mm2. Drop is 2 × 20 × 27.8 × 0.0172 ÷ 10 = 1.913 V. That's 1.913 ÷ 83 × 100 = 2.30 percent, which fails. Ampacity of 57 A is fine, but the drop isn't.

Try 16 mm2. Drop is 19.126 ÷ 16 = 1.195 V, or 1.44 percent. Ampacity of 76 A passes. The answer is 16 mm2.

Cut the run to 10 m and the drop on 6 mm2 is 1.92 percent, with 41 A of ampacity. A 6 mm2 cable works there. Doubling the length doubled the drop, which pushed the answer up two sizes.

Does Gauge vs mm2 Really Matter?

It matters when you shop. Metric countries sell solar cable in mm2. The US sells it by AWG, where a bigger number means a thinner wire. The two scales don't line up exactly, so use the area in mm2 for the math and pick the nearest size at or above it. The AWG glossary entry has more on how the numbers run.

| Metric Size | Ampacity | AWG Size | Area | Ampacity | | --- | --- | --- | --- | --- | | 4 mm2 | 32 A | 12 AWG | 3.31 mm2 | 25 A | | 6 mm2 | 41 A | 10 AWG | 5.26 mm2 | 35 A | | 10 mm2 | 57 A | 8 AWG | 8.37 mm2 | 50 A | | 16 mm2 | 76 A | 6 AWG | 13.3 mm2 | 65 A | | 25 mm2 | 101 A | 4 AWG | 21.2 mm2 | 85 A |

These ampacities are conservative figures from the site's tables. Your local code may allow different values.

Worked example · Three Panels in Arizona

A home in Arizona has three 400 W panels in series. Example datasheet values are Vmp 37 V and Isc 11 A. The one-way run is 30 ft, or 9.144 m.

  • String voltage is 37 × 3 = 111 V
  • Current is 11 A, with one string
  • Ampacity needed is 11 × 1.25 = 13.75 A

16 AWG has 13 A of ampacity, which is too thin. 14 AWG has 20 A, and its drop is 2 × 9.144 × 11 × 0.0172 ÷ 2.08 = 1.664 V. That's 1.664 ÷ 111 × 100 = 1.50 percent. The answer is 14 AWG.

Stretch the run to 60 ft (18.288 m) and 14 AWG drops 3.00 percent, which fails. 12 AWG gives 1.88 percent and passes.

Now wire the same three panels in parallel. String voltage falls to 37 V and current rises to 33 A. The 30 ft run then needs 4 AWG, at 1.32 percent. Same panels, same distance, but the wire is far fatter.

Can I Just Use What I've Got?

Maybe, but test it first. Leftover cable is fine when it passes both checks. Run its area through the drop formula, and compare its ampacity to 1.25 × Isc × strings. If either check fails, it's too thin for that run.

Wire that's too thin gets warm under load, and it wastes power every day. Fusing matters as much as wire size here. See the guide on the right fuse between panels and controller, and size the fuse so it protects the wire you pick.

What Comes After the Controller?

The other half of the system carries more amps at a lower voltage. That run is usually short, but it still needs careful sizing. Read what size wire from the charge controller to the battery next. The charge controller calculator gives you the amp rating you'll need for that step.

Local electrical code applies to every part of the array wiring, including PV cable type, conduit, and disconnects. A qualified installer should check the final design before you wire it up.

Related Calculators and Guides

Results are estimates based on typical values and the settings above. Local electrical codes apply, and a qualified installer should check the final design before you buy or wire anything. Read the full disclaimer.