Offgrid Atlas

What Size Wire From the Charge Controller to the Battery

5 min read · Published 2026-11-17 · Last updated 2026-11-17 · Offgrid Atlas Editorial

For a 600 W array on a 24 V battery bank, the wire from the charge controller to the battery needs to be 6 mm2 if the run is 3 m. That cable is rated for 41 A against a 31.25 A design current, and it loses 1.79 percent in the run. The battery side is where thin wire hurts most, because the amps are high and the voltage is low. This guide walks through the math so you can find your own size.

How Many Amps Run Between Controller and Battery?

Power comes out of the controller at battery voltage. So the amps depend on the battery, not the panels. Divide the array watts by the battery voltage to get the running current.

Then add a 25 percent margin. That design current is the same number as the MPPT controller rating before you round up to a standard size. The charge controller calculator shows both numbers.

Formula

Running A = array W ÷ battery V, and design A = running A × 1.25

The wire's ampacity has to be at least the design current.

The drop check uses the running current. The ampacity check uses the design current. A size has to pass both.

What Gauge Wire Keeps Voltage Drop Low?

The site limits drop to 2 percent here. Battery voltage is the reference, so 2 percent of 12 V is only 0.24 V. That's a tiny budget, and it's why battery cable gets thick fast.

Formula

Drop % = (2 × length m × running A × 0.0172 ÷ wire mm2) ÷ battery V × 100

Length is one way, from the controller terminal to the battery terminal.

Rounding matters. Work out the drop in volts first, then divide by battery voltage, and round the final percent to two decimals. For more on why this loss counts, see voltage drop.

Worked example · A 600 W Array in Kenya

A lodge in Kenya has a 600 W array and a 24 V battery bank. The controller sits 3 m from the battery.

  • Running current is 600 ÷ 24 = 25 A
  • Design current is 25 × 1.25 = 31.25 A, so a 40 A controller
  • Ampacity needed is 31.25 A

Try 4 mm2. Drop is 2 × 3 × 25 × 0.0172 ÷ 4 = 0.645 V. That's 0.645 ÷ 24 × 100 = 2.69 percent, which fails.

Try 6 mm2. Drop is 2.58 ÷ 6 = 0.43 V, or 1.79 percent. Ampacity is 41 A, which clears 31.25 A. The answer is 6 mm2.

Why Does Battery Voltage Change the Wire Size?

The same power at a lower voltage needs more amps. More amps mean more drop, and drop is measured against a smaller voltage. Both effects work against you at 12 V.

| Battery Voltage | Array | Running Current | Design Current | | --- | --- | --- | --- | | 12 V | 400 W | 33.3 A | 41.7 A | | 24 V | 400 W | 16.7 A | 20.8 A | | 48 V | 400 W | 8.3 A | 10.4 A |

Moving a 400 W array from 12 V to 24 V halves the current. The wire you need can drop several sizes. The guide to sizing an off-grid system explains how system voltage gets chosen.

Worked example · A 400 W Array in Australia

A caravan in Australia has a 400 W array and a 2 m run, sized in AWG.

At 12 V, running current is 400 ÷ 12 = 33.33 A and design current is 41.67 A. 8 AWG has 50 A of ampacity, but its drop is 2 × 2 × 33.33 × 0.0172 ÷ 8.37 = 0.274 V, or 2.28 percent. That fails. 6 AWG gives 0.172 V, or 1.44 percent, and has 65 A of ampacity. The answer is 6 AWG.

At 24 V, running current is 16.67 A and design current is 20.83 A. 14 AWG has 20 A of ampacity, which is just short. 12 AWG has 25 A and a drop of 1.44 percent. The answer is 12 AWG.

Double the 12 V run to 4 m and 6 AWG climbs to 2.87 percent, so it fails. 4 AWG gives 1.80 percent and passes.

Will It Melt If the Wire Is Too Thin?

Thin wire heats up when current is high. That's the ampacity check, and it protects the insulation. The drop check protects your charging performance. A wire can pass one and fail the other, so run both.

Here's a case where ampacity decides it. A 3,000 W array on a 48 V bank in Norway has a 2 m run. Running current is 3,000 ÷ 48 = 62.5 A, and design current is 78.125 A. 16 mm2 has a drop of just 0.56 percent. But its 76 A ampacity is below 78.125 A, so it fails. 25 mm2 has 101 A and a drop of 0.36 percent. The answer is 25 mm2.

Check the other end too. The guide to fusing between battery and inverter covers the larger cables on the load side, and the panel-side fuse guide covers the PV circuit.

How Thick Should the Wire Be When the Run Gets Long?

Keep the controller close to the battery. Drop scales with length, so doubling the run doubles the loss. Short runs let you use cheaper, easier cable.

If the run can't be short, you have three options.

  • Use a thicker cable
  • Raise the battery voltage, such as 24 V instead of 12 V
  • Move the controller closer, and lengthen the cable on the panel side instead

That last option works because the panel side runs at a higher voltage. The panel-side wire guide shows how much longer that run can be. Panel-side drop costs less than battery-side drop.

Final Checks Before You Hook It Up

Pick the size, then confirm a few details.

  • Use cable rated for battery current, with proper lugs and a tight crimp
  • Match the positive and negative cables in length and size
  • Fuse the battery lead close to the battery, sized to protect the wire
  • Check the controller manual for its largest terminal size

Use the solar wire size calculator to test your numbers, and the battery bank size calculator if you're still choosing a voltage. Local electrical code applies to battery cable, fusing, and disconnects. A qualified installer should check the final design.

Related Calculators and Guides

Results are estimates based on typical values and the settings above. Local electrical codes apply, and a qualified installer should check the final design before you buy or wire anything. Read the full disclaimer.